Lip2000 is supplied in liquid form at a concentration of 1mg/ml. Store at 4℃.DO NOT FREEZE.

Product Qualification

Lip2000 has been extensively tested by transfection of HEK293 cells with an EGFP reporter containing plasmid. Lip2000 is free of microbial contamination.

Important Guidelines

Follow these guidelines when performing transfections:

1. The ratio of DNA (in μg) :

Lip2000 (in μl) to use when preparing complexes should be 1:2 to 1:3 for most cell lines. To transfect 0.5 -2 ×10⁵cells in a 24-well format, use 0.8-1 μg DNA and 2-3 μl of Lip2000. Optimizing transfection by varying DNA/Lip2000 ratio is possible.

2. It isCRITICALto transfect cells at high cell density. 90-95% confluence the time of transfection is recommended to obtain high efficiency and expression levels and to minimize decreased cell growth associated with high transfection activity.

Lower cell densities are suitable with optimization of conditions. Take care to maintain a standard seeding protocol between experiments because transfection efficiency is dependent on culture confluence.

3.DO NOTadd antibiotics to media during transfection as this will cause cell death.

For better results, you may choose to:

Use Opti-MEM I medium to dilute Lip2000 prior to complexing with DNA. Other media without serum (e.g.DMEM) may be used to dilute Lip2000,but transfection efficiency may be compromised.

Note:Some serum-free formulations can inhibit Lip2000 mediated transfection, for example:CD 293, 293 SFM II, and VP-SFM etc.

Transfection Procedure for 24-Well Format

For adherent cells:One day before transfection,plate cells in growth medium (without antibiotics) so that they will be 90-95% confluent at the time of transfection (0.5 -2 ×10⁵cells/well for a 24-well plate).

For suspension cells: On the day of transfection just prior to preparing complexes,plate 4-8×10⁵cells/500 μl of growth medium (without antibiotics) in a 24-well plate.

1. For each transfection sample, prepare DNA-Lip2000 complexes as follows:

? Dilute DNA in 50 μl of Opti-MEM I Reduced Serum Medium without serum (or other medium without serum).Mix gently.

? Mix Lip2000 gently before use, then dilute the appropriate amount in 50 μl

of Opti-MEM I Medium (or other medium without serum). Mix gently and incubate for 5 minutes at room temperature.

Note: Combine the diluted Lip2000 with the diluted DNA within 30 minutes. Longer incubation times may decrease activity. If DMEM is used as a diluent for the Lip2000, mix with the diluted DNA within 5 minutes. After the 5 minute incubation,combine the diluted DNA with the diluted Lip2000 (total volume is 100 μl).

?Mix gently and incubate for 20 minutes at room temperature to allow the DNALip2000 complexes to form. The solution may appear cloudy,but this will not inhibit the transfection.

Note:DNA-Lip2000 complexes are stable for at least 5 hours at room temperature.

2. Add the 100 μl of DNA-Lip2000 complexes to each well. Mix gently by rocking the plate back and forth.

3. Incubate the cells at 37℃ in a CO2 incubator for 24-48 hours until they are ready to assay for transgene expression. It is not necessary to remove the complexes or change the medium; however,growth medium may be replaced after 4-6 hours without loss of transfection activity.

For stable cell lines:Passage the cells at a 1:10 or higher dilution into fresh growth medium 24 hours after transfection. Add selective medium the following day.

For suspension cells:Add PMA and/or PHA (if desired) 4 hours after adding the DNA-Lip2000 complexes to the cells.

Tip: For Jurkat cells, adding PHA-L and PMA at final concentrations of 1 μg/ml and 50 ng/ml, respectively, enhances CMV promoter activity and gene expression. For K562 cells, adding PMA alone is sufficient to enhance promoter

activity.

Scaling Up or Down Transfections

To transfect cells in different tissue culture formats, vary the amounts of Lip2000 , DNA, cells, and medium used in proportion to the difference in surface area (see table below). With automated, highthroughput systems, larger complexing volumes are recommended for transfections in 96-well plates. Note: You may perform rapid 96-well plate transfections (plate cells and transfect simultaneously) by adding a suspension of cells directly to complexes prepared in the plate. Prepare complexes and add cells at twice the cell density as

Note：Product information may be optimized and upgraded. Please refer to the actual label information for accuracy.