Propylene dextran gel S-500

Allyl glucan gel series fillers are allyl glucan and N, N' The crosslinked copolymer of -methylene bisacrylamide has an average particle size of 50μm, while increasing the rigidity of the matrix, ensuring fast flow characteristics and high resolution.

Separation range

4×10⁴ ~ 2×10⁷ (globulin)

Storage conditions

The product should be sealed and stored in a ventilated, dry and clean place between 4℃and 25℃(the storage solution is 20% ethanol), and cannot be frozen. The used column is stored at 4℃(20% ethanol), shelf life: 2 years.

Usage

Separation filler used for purification and separation of protein and other substances. This product is for scientific research only and shall not be used for other purposes.

Procedure

1 column loading

(1) Equilibrate all materials and reagents to the temperature of the chromatographic experiment. The buffer is prepared and all buffers are degassed.

(2) Check all components of the chromatographic column, especially whether the filter, sealing ring, screw plug is tight, and whether the glass tube is clean and complete.

(3) Take the appropriate amount of gel according to the demand, and clean 20% ethanol with deionized water.

(4) Wet the bottom of the column with water or buffer and maintain a small level, be sure to make the bottom of the bubble free.

(5) Use a glass rod to guide the homogenate along the inner wall of the column into the column at one time, taking care not to produce bubbles. Open the liquid outlet of the column, make the gel settle freely in the column, and connect the top of the column.

(6) Open the peristaltic pump, so that the buffer flow rate of 1.33 times the flow rate of use, so that the column bed is stable (pay attention to the pressure does not exceed the maximum pressure of the packing).

2 Balance

Balance the chromatographic column for at least 5-10 column volumes before loading until the baseline of the recorder becomes stable (the pH and conductance of the effluent are equal to the pH and conductance of the upper column Buffer).

3 Sample loading

(1) The sample is prepared with balanced liquid, the sample must be centrifuged or filtered after sampling (0.45um filter membrane), if the sample salt concentration is too large, it needs to be treated before sampling.

(2) The recommended loading volume does not exceed 5% of the column volume.

4 elution

Eluting with buffer, keep the flow rate and buffer composition unchanged during elution.

5 Regeneration is generally washed with buffer to balance and can be used again. In some applications, substances such as denatured proteins or liposomes cannot be washed off during regeneration.

The following situations must be cleaned and regenerated:

(1) Increased back pressure;

(2) Color changes at the top of the column;

(3) resolution reduction;

(4) There is a gap between the conversion joint and the gel surface.

If an increase in pressure is observed, check the individual filter valves and filter membranes in the line for contamination before starting the column cleaning procedure, and then remove precipitated proteins, non-specifically bound proteins and lipoproteins by washing the column with 0.1MNaOH.

Precautions

(1) Before loading the sample, the sample must be filtered through the membrane and remove the pigment, otherwise the impurities and pigments will be adsorbed on the filler, affecting the normal use of the filler. All buffers need to be filtered with a 0.45um filter.

(2) In the process of use, avoid using high concentrations of strong acids and bases, and the concentration of acids and bases should be less than 0.1 moles. The alkali will slow the flow.

(3) Different samples, adsorption and elution methods are different, can be carried out according to the relevant literature.

Note：Product information may be optimized and upgraded. Please refer to the actual label information for accuracy.

Remark：These protocols are for reference only. Solarbio does not independently validate these methods.

Note：

1. The products are all for scientific research use only. Do not use it for medical, clinical diagnosis or treatment, food and cosmetics, etc. Do not store them in ordinary residential areas.

2. For your safety and health, please wear laboratory clothes, disposable gloves and masks.

3. The experimental results may be affected by many factors, after-sale service is limited to the product itself and does not involve other compensation.